Miter Saws Reviews

I had a good Delta blade on my Delta miter saw for almost 8 years. So I'm used to good blades. I work with all kinds of wood. Maple, Oak, Walnut, including plywood. This blade cuts it all great. No chips, splinters, and it is extremely sharp. You can hardly feel the blade hit the wood. The end grain cut is amazingly smooth.

I went and ordered a combo blade from Freud for my tablesaw.

The title says it all, you can't beat this blade. I really don't think there is any room for improvement here. I don't know what I did without it before! If you've got a decent chopsaw and a stock blade, you are missing out. This blade supercharges your miter box with glass-smooth cuts, less tear-out, thick carbide for many resharpenings, no blade flex (that I noticed) and therefore, perfect finish grade crosscuts. Leaves the edges as sharp as can be. Be careful when you first take it out of the box, this blade is truly sharp. YOU NEED THIS BLADE! Now I'm looking for more Freud products. Way to go Freud!!

We have tried all types of blades. And some are better than others!

When your making some of the finest cabinets and doors in the world for some of the most demanding customers you can't second guess your self! Or worrie about your saw blades integrity!

These blades will amaze your customers with fine bevels and hair line tight cross cut joints at any angel with any type of wood!! Great for cabinet panal saws and compound radial sliders! In 10" size.

When asked how we get our cuts so tight, we tell them about the Freud 80-tooth LU85R010 "Ultimate Crosscutting" blade! If your as serious about your projects as we are about ours don't skimp on your crosscut blades! Buy the LU85R010 From Freud!

And Fillet Your Wood!

This is a nice saw for the money, no problems with it. I've had one project where I wish I had a 12-inch saw or sliding miter, otherwise this works for everything around the house from chopping 2x4's to fine trim work. It's light and easily moved too. The blade that comes with it is OK and works for trim work, but it would be nice if an 80-tooth blade was included!

I've had this saw for a couple of years. It is a great saw that has never bogged down or been at a loss for power. The horizontal handle is superb. The blade is not that bad either, however it did splinter some oak & some plywood I recently cut. The only drawback is the size. I recently had to cut some shelves that were 9" wide; too big for the saw. I wish I had the 10" sliding saw (36-240). If you plan to keep your projects small to medium sized this is an excellent saw. ! If you are doing larger projects, i.e. shelves, bookcases, etc. then invest in the Delta Sidekick 36-240 sliding miter saw. I have also added a LaserKerf to mine, which is a great addition ...Over all, this saw is phenomenal for the price and I am going to continue to buy Delta products.

Excellent tool. Easy to assemble and the manual makes it easy to learn how to use. Comes with a very good blade and the side and back extensions are a great asset. The tool is easy to learn and use and is very well finished. Spending more money would be a waste of time.

If you are looking for THE absolute best blade for your Sliding Compound Miter Saw (SCMS) look no further than the FORREST ChopMaster blades.

I use the ChopMaster on my 12", 10" and 7 1/2" SCMS and these are by far the best blades I have ever used - cuts are as smooth as butter!

Mike

Forrest Blades will increase your saw's felt horsepower many fold. They are the very best I have ever used. And I have used them for 15 yrs. You can bet I will continue to use them on all of my saws.

I had an older Dewalt finishing blade on my Dewalt Miter Saw and decided to upgrade. I got the Forrest 12" Chopmaster on sale at Amazon and it was a great purchase. I used to get a lot of tear out with the Dewalt and now the Chopmaster cuts like butter. I own the WWII and the Dado King from Forrest. You pay a little more for Forrest, but if you need quality cuts, Forrest is the way to go!!!

In keeping this breif. I have an old model DeWalt that I have been struggling with hardwood rips on. Since I got this Freud blade the problems are gone, cuts are smoothe as can be. I will buy this product again.

Have I compared this saw blade to every one on the market? No. But I am very satisfied with the purchase. I have a underpowered Bosch 4000 portable table saw. With the combination blade that came with the saw I could barely rip 3/4" cherry. It would leave horrible burn marks and take a lot of pressure to get it through. Not safe. After receiving this blade, I've ripped Cherry, Walnut, and Ash, up to 1". All cuts have been burn free, and its been much easier to get through. I'm also surprised by how much quieter it is. My wife even noticed and asked me why my saw was so much quieter when I came upstairs after testing it out. And remember... this is a RIP saw. It does not like to be used for crosscutting. I tried a crosscut just for experimentation... it was tough to get through and left burn marks. So don't try to use this as a combination blade. I paid $40 for it and was happy... I see now that it's $25. I was happy spending $40, so if you can pick it up for $25 I think you're getting a great bargain for it. Of course, when I originally put it in my shopping cart, the price was $25, but by the time I purchased it Amazon bumped the price to $40. I couldn't wait for it to go back down, so had to eat the extra $15. I love Amazon, but I'm getting tired of big price jumps after I put things in the cart and a day or two passes.

This IS THE BLADE that you want if you are using a weak motor saw like the Ryobi BT 3000. Rips very nicely without bogging down the weak motor. I rip alot of 1 " stock and plywood and it slices through it with little effort and great feed rate. I think that it's a great blade for as little as you pay for it. I know that I'll buy this blade again whanever this one wears out.

I have owned this saw for over 3 years now. It is a shame that I had paid the full introductory price when it had come out, but I wouldn't trade this saw for anything. I also own the complete 24V cordless line by Bosch. I own a small contractor buisness doing everything from kitchens, baths, additions, full house construction, to concrete work and everything in between. Not only is this saw worth it's weight in gold, but the entire 24V Bosch is worth the same. I can not write a good enough review for this item. It is so handy to set up and cut a few pieces of trim with such accuracy as my 12" Bosch Sliding Compound miter saw. In fact, I have found myself using this saw for just about every job, since I already have the case with my other cordless tools. I have trimmed out $750k houses with this saw, just set it up in every room that needs trimwork, hook it up to my shop vac and away I go with accurate miters. The only thing that I had wished this saw had was the dual compound feature, but I am used to turning crown over and cutting it the other way. The saw holds an accurate fence and the positive miter detents are right on! Again, it takes only 5 min. to pull the saw out, set it down, and begin cutting with no cords to drag around. It is the nearest replacement to a quality cordes miter saw you can ever have. I am truely convinced to forever puchase the old blue and red over the yellow and black any day. Bravo Bosch!

L. Long, L Squared Building and Excavating

well ive had this saw for a month now. i couldnt be happier i install kitchens and bath cabinets everyday and use it everyday, the battery lasted longer than i thought it would before i had to recharge it. its so light my helper dosent complain anymore about dragging the saw around. between this and the bosch cordless jigsaw and the nail gun i hardly have to plug in anything anymore i read some of the reviews before i bought this last saw most were favorable some wernt but for what i do its great i guess if i did trim all day i would want 2 batteries but thats the only down side

First let me say I am not a contractor I am a weekend warrior but I do like doing my own project work.
I bought this saw about 2 months ago because I had a project to build a double set of outside stairs. The nearest power was 1/4 mile away and I don't own a generator.
This saw is very good. I was suprised by it power. The stairs I built were completely made from green treated lumber. I was able to cut 2x12 stair treads with no problem. Yes I had to flip the wood over and yes the wood was still wet. I was amazed. I also bought the 24 volt circular saw. It too exceeded my expectation. I also own the Corded Dewalt 12 inch compound miter. This saw can't do everything the Dewalt can do but you can't expect it to. For what it is worth I have not found a job it can't do yet.
I would highly recommend this saw to any one.

Without a doubt, the very best blade I've used on my Makita Slide/Compound Miter Saw. I am a Contractor/Trim Carpenter and have used many different blades over the years. You simply can't go wrong with this product. Not the least expensive blade by any means, but unquestionably the best.

This blade is worth it's high cost! The cuts are smooth as glass and there is very little or no splintering on the back side. I would recomend this to anyone that is tired of poor quality cuts produced by other blades.

This is a dream saw blade for precise miter cuts. You won't believe how clean and smooth your finished cuts are. No sanding required! I can't say enough about this tool other than I wish it wasn't so darned expensive. But, believe me, you get what you pay for.

If you are still using the blade that came with your contractor style table saw, then this is a quality, affordable upgrade. It cuts well, has very little run out, and leaves a nice edge. The carbide on the tips is good and thick and will stand several re-sharpenings.

The only drawbacks? There is some vibration and rip cuts are not mirror smooth. If you work on small projects and every cut must be perfect then spend the extra bucks and get a Woodworker II by Forrest.

bought this blade for framing construction. i use it in a makita 10" csm. it didnt take long to see it was a winner. the blade has nice beefy carbide on it which means more sharpenings and longer life. something i noticed immediately was the snug fit on the arbor. most blades i have used apparently had a little slop to them. i like this blade alot and cant wait to try the 30 tooth glue rip blade.

This blade was a replacement for my factory blade that came with my Ridgid table saw. Alot of carbide for additional sharpenings. Cuts like butter;thru oak, cherry, etc. It cuts through veneer, and 12/4 red oak stock with zero tear out. Leaves a virtually glass like edge for edge joint glueing. I should have bought this blade earlier!!!! I looked at Freud, and Forrest. But the cost brought me back to this blade. I'm hooked on Systimatic

I own a dozen or so great blades, but one of these came with my new Unisaw, and I was amazed at how well it performed. I use a lot of MDF, which is very abrasive, and tough on carbide, and I cut about 800 feet of cabinet rails and stiles, and trim pieces before the blade showed any signs of wear. This is very good life for MDF. Rips hardwood very good, and crosscuts well also. It is a better blade than the CMT products at a much lower price. Razor sharp cuts with MDF, and runs straight and Quiet. Lasts longer than the Woodworking Wizards and Signatures from Oldham, although they are top notch as well. I save my favorites, the Forrests, for furniture. You can't go wrong with this one!! I ordered another one to use while my first one is out being sharpened.

Awesome combination blade. Clean crosscuts and decent rips. You can't go wrong! I have two.

This is an excellent combination blade at a great price. It produces very smooth, finished cuts with no visible saw marks. I no longer need to run boards through the jointer before panel glue-ups. I have cut hundreds of feet of Oak and Cherry with it (enough to build a dresser, chest of drawers, two night stands, a bookshelf, and a wall shelf) and the blade is still sharp! Delta even threw in two coupons for free sharpenings. Bravo on this one, Delta!

Yes, just like other customer has mentioned. I got the package that look like it has been repackaged. It doesn't look brand new but also it doesn't look like it has been used. However, mine has come with a broken leg so I have to RMA it.

I am interested in knowing if any others who ordered, got upon receipt of the box, a repackaged unit. Seems to work OK, but definately does not appear to be a new unopened item. Please post, and let me know. Thanks. I did not see where these were refurbs or "other than new", in the original itme listing.

I just mounted a 10" model to a Hitachi stand. Beware of the adjustable arms that come with the saw. Mine lifted the wood, making it uneven as I tighted the adjustable wood supporting arms. The stand helps, because you don't have to use the Makita supports. I have yet to contact Makita about the problem.

I would however reccommend the Home Depot Miter Saw stand for $200. It has very large wheels and it is very easy to move, and extremely stable.

This is not a review. This is just a bit of information for a potential buyer who may be looking for additional information on the 78-939 Cut-Off Stop product.

The link on this product description page, to the PDF product manual is wrong. Instead of taking you to the 78-939 Cut-Off Stop for T-Square Fences product manual, it takes you instead to the Biesemeyer T-Square Miter Saw Table Instruction Manual. This is kind of sad since I was interested in obtaining a lot more information about the Cut-Off Stop than was given in the sparse product description. I gave the product 3 stars because I had to rate this item to get the review published and I didn't want to be unfair.

I informed Amazon about this problem months ago but I see that nothing has changed.

It scores for function and safety but I had to remove excess paint to make it parrallel to the fence. This also improved the thickness dimension from over 1-1/32" to 1-1/64". It should be considered an essential tool for safety. I had the bruises to prove it after years of dumb luck.

I've been delaying buying this for years, but finally did it. I have been very happy with it's performance so far. Much easier than clamping a scrap on the fence.