Table Saws Reviews

Because the screw issue has not been resolved (see other reviews), assembly can be maddening. It is too heavy: sturdy is good, but this gauge is awkwardly heavy. Without a T-slot (and maybe even a lateral table extension), anything but narrow stock will have this gauge falling off the table.

Reviews here imply this is a "must have" for precision work. Fastening a milled board to a conventional gauge (preferably with an adjustable rod, to eliminate lateral play) and clamping on a stop on occasion has a lot going for it.

The JDS 18-34 Accu-Miter Gauge does everything it claims it can do.It was simple to assemble and adjust it.Adjustments have held true so far.I've used it alot in the short time I've had it. Comparing it to 3 other miter gauges I have its by far the best, but I feel it should be. I paid the price for a quality tool and got one.

This is a rock-solid mitre gage. Easy to set up and use. There are two stops on the gage and both are easy to use and produce extremely repeatable cuts. Customer service at JDS is efficient and nice. (I accidently knocked the gage off of the workbench and one of the stops broke. JDS quickly shipped a replacement for a nominal fee, $4). It's an expensive gage. But, I do so much cross cutting that the cost is justified.

If you purchase this jig, be prepared for extensive modification to make it usable. I had to resurface the clamping face to remove a deep cup, and replace the useless depth scale with a cursor. The back stop is a scrap of angle steel that had to be filed flat and square. Worst of all, the clamping pad guide bar hole was bored so far off center to the locking handle that the clamp screw handle angled clear into the saw tabletop at full extension. Not exactly conducive to clamping! It required machining a keyway with a guide pin to hold everything level. On the plus side, the unit is cast iron and very solid and accurate. Tenon width is controlled by an excellent locking leadscrew mechanism that performs well. All in all if you have a milling machine handy and want to invest a few hours correcting shoddy workmanship, you'll end up with a fine tool. My unit was not usable as shipped. I corrected the problems rather than return the jig, suspecting a replacement would be no better.

I was going to buy this jig. So I went and compared it at the local woodworking store. The Powermatic and Jet jigs are exactly the same, except for the paint. The Jet model is $20.00 cheaper. If you look at the pictures of the two here on Amazon, you'll see that whoever took the photos used the exact same piece of wood even. Don't waste your money on gold paint instead of white, they both come from Tiawan.

This tenon jig is by far the heaviest duty jig that I have tried. I love all the adjustments and the precision it offers. I did have to run the bar on my beltsander for five seconds to get it to slide perfectly in my Ridgid's mitre slot, but that is because the Ridgid uses a non industry standard mitre slot width.

This jig feels very solid and safe to use even with long thick table legs.

I use a router with a jig for my mortises so since I had my templates made already I setup the tenon jig to fit my mortices...with the precision micro adjust and my dado blade, I made perfect mortise and tenons on the first practice cut.

I also made some compound angled tenons, and because the jig was nice and "beefy" it held the stock perfectly even using an extreme angle...again the test cut fit my mortises perfectly.

This is good stuff!

I have a small home shop, and purchased this saw about 3 weeks ago. I love it. I don't do any heavy production work, just furniture and cabinet work, and this is the perfect saw. I can honestly say that I will have this saw for a long time. Power is great, blade control is excellent, and the 50" Biesmeyer fence system is spot on accurate. I highly recommend this saw to anyone looking to purchase a cabinet style table saw. Delta is the best.

I am very happy with the purchase of the 36-821L Unisaw. Although they do not specify it, you need to order or build the right extension table or you will not be able to use the saw correctly. It seems that the saw comes with all the parts needed for the extension table except for the most important part, the extension table. I decided to build my own extension table and it ended up costing me half the price. The saw was very easy to put together, it did not take 5-6 hours like the other reviews stated. Only one problem with the saw so far and that is that the on/off switch seems to be defective and although the saw does work, i will have to get in touch with... and/or Delta to fix the problem. It also does come with a very wimpy blade so you should upgrade it as soon as possible.

I bought the Delta left tilt arbor Unisaw. I'm very happy with it. I could have purchased either the Powermatic or the General. The attention to detail on the machining seems better on the Delta than the other machines.

The previous reviewer, Richard, stated that he used 18 AWG wire to replace the cord on his saw. I believe that is a typo and that Richard meant 10 AWG wire since 10 ga is the recommended wire size for a 30A circuit. I bought a length of SOOW 10/3 with the same NEMA L6-30P plug and NEMA L6-30R receptacle that Richard recommended. Don't forget strain relief on your cord, especially if using an overhead outlet. I used the Hubbell 073041279 bus grip attached to a hook screwed into the ceiling.

I like this saw a lot. Over the years I have used many different table saws and very few will equal the quality of this machine, especially for the money. Set up was a breeze and needed only minor adjustments.

I do have a complaint but it is not about the quality of the saw but with the quality of organizational skills of the people in charge of sending out the $500 coupon book and free mobile base. It's been 9 weeks since I purchased the saw and still no coupon book or mobile base. It would have been nice to have the mobile base with the table saw so that during the assembly process the saw could have been assembled on the base.

If you want an accurate and powerful table saw this is it, but don't have the expectation that your freebies will arrive with it, shortly after or in the near future.

I recently purchased a Delta L51X Left Tilt 5 horse power Unisaw with the 52 inch Biesemeyer fence and the side extension table. Since I like to move my equipment around the shop either for cleaning or for re-arranging I also purchased the Delta 50-289 Mobile Machine Base for the Unisaw with a 52 inch Biesemeyer fence. To my dismay shortly after I ordered the saw and mobile base, Delta began offering the base as part of the total saw package at the same price. In this case you might say the early bird got the shaft.

I would like this review to be helpful to those who read it so I have divided my comments into four specific paragraphs 1.) My motivation and incentive for purchasing the Delta Table Saw, 2.) My thoughts on the packing, shipping and delivery of the saw, 3.) My thoughts and experience on the assembly of the saw, and 4.) my experience in using the saw.

________________________________________________
Motivation and incentive for purchasing the Delta Unisaw
________________________________________________

I had been looking for a saw of this type for over a year. I finally decided on purchasing the Unisaw from Delta through Amazon.com because the price of the saw was down by more than $200 from its price a year ago, and because Amazon.com was offering free shipping for this heavy machine. I also was interested in the free tool and the $500 tool accessory coupon book that Delta was offering in its promotion to sell this saw.

When the saw arrived, inside the carton was a mail in post card that allowed me to select one of four items as my free tool. The four items were: 1.) a mobile base for any one of several tools from drill presses to lathes, 2.) a Delta cordless drill, 3.) a Porter Cable nail gun and 4.) a Porter Cable Router. I didn't need a mobile base so I checked out the remaining tools on the Amazon.com website. The Delta cordless drill is no longer being manufactured. The user reviews on the Amazon site for this drill were mostly negative. The reviews for the Porter Cable nail gun and the Porter Cable router were for the most part very positive. I didn't need any of these tools but I selected the router. Perhaps it might be useful as a Christmas present for some young wood worker who is just getting his repertoire of tools established.

The bad news is you have to make your selection on the post card and then wait 6 to 8 weeks to get your tool and the $500 coupon book. It would have been to Delta's advantage to ship the coupon book with the saw so the excited new saw owner could make a few more purchases of saw accessories before the warm glow of a new purchase wore off. Looks like the Delta marketing people weren't thinking too clearly. Perhaps the people who do the marketing for Delta are descendents of the flower power generation.

Overall grade B. My grade would have been an A if the coupon book had been shipped with the saw.


______________________________
Packing, Shipping and Delivery
______________________________

The saw was shipped in four heavy cardboard cartons. The saw itself was in one large carton weighing in a little less than 500 pounds. The Biesemeyer fence was shipped in two cartons and the side extension table was shipped in a separate carton. The packing was excellent, and of much higher quality than what I have previously experienced with shipments of heavy equipment from Grizzly. All items were packed well and reached my doorstep in good condition.

The method of shipping was poor as usual. The shipment arrived on a large delivery truck with no lift gate, and with a woman driver. Nothing against women but how in the heck is a woman even with my help going to lift a 500 pound carton to the ground from the back end of a trailer whose floor height was above her shoulders. I asked her why not take the shipment back to their dock and re-load it on a truck with a lift gate. She said that was possible but her shipping companies dock was in Blythe California and my shipment would have to be shipped all the way back to Blythe in order to make the transfer. Since I live in Prescott Arizona this was not an option for me.

Fortunately there is a house under construction a block away from mine. I called two friends, we borrowed two 2x6 x 8 foot scaffold planks from the house under construction and laid them on the trailer floor spaced about 2 foot apart. We then placed the 500 pound carton on its side on the two planks with the bottom pallet side of the carton facing out the trailer door. Then we pulled the planks out of the trailer along with the carton until it began to teeter on the trailer edge. We then lowered the ends of the planks to the ground and let the saw slide down the incline of about 30 degrees to the ground where we used a dolly to move it to my shop. The lady truck driver was very patient as she watched all this. I think she was a little surprised that ordinary non truck driving males could be so resourceful.

I give this task an overall Grade of B. I would have given the trucking company a grade of D but the woman truck driver was kind enough to wait until my friends arrived from across town to help unload the saw and because there was no visible damage like fork lift holes or crushed corners on any of the cartons when I received them. It's also nice to have friends who can help turn a bad situation into a good one.

__________________________
Assembly of the Saw
__________________________

The Unisaw is heavy. If you add the 52 inch Biesemeyer fence, guide tube, angle iron mounts and side extension table, it gets a whole lot heavier.

I bought the mobile base and I would strongly recommend you buy it too if you decide to purchase the saw. Although the directions are poor, the base assembles quickly and easily, and it works great. A simple foot pedal that locks into place raises the base up onto three wheels and the Unisaw can be easily moved by a single person. A simple hand lever releases the lock and the stand lowers back to the floor where it sits on rubber feet that are individually adjustable to compensate for floors that are out of level.

Assembly of the Unisaw itself is time consuming. In order to assemble the Unisaw, Biesemeyer Fence, and side extension table you will need the help of at least one other person. You will also need at least one 8 foot pipe clamp, four Quik clamps, two 2x4's at least 4 foot long, several wood shims, a drill with a 1/4 inch bit, a 3/16 inch allen wrench, a socket set, a large Phillips screw driver, a small crescent wrench, a 9/16 inch open end wrench, some red rags and a can of solvent to clean the packing grease off the machined cast iron parts.

The Unisaw comes attached to a wooden pallet with bolts that have 3/16 inch allen wrench heads of all things. It would have been more practical to use � inch hex head bolts but perhaps the packaging people at Delta like to pull practical jokes on unsuspecting new saw owners.

The Unisaw comes with the two detached cast iron wings. They are very heavy. They need to be cleaned with solvent on all edges so they mate well with the saw table bed.
The wings need to be aligned with the top of the saw table so they are in the same horizontal plane and so there is no noticeable discontinuity along the edge where the wings and the table join. This is not easy because the wings are so heavy. It's difficult to hold the wings and tighten the mounting bolts at the same time. Better to have a second person hold the heavy wings, tighten the bolts just enough to hold them in place then use the palm of your hand as a mallet to move the wings up or down to align the tops to the plane of the saw table. All other items in the assembly of the saw itself are reasonably simple.

Assembly of the side extension table and the Biesemeyer Fence system is labor intensive and is a good candidate for requiring the help of a second person. I strongly recommend that you read the entire instruction manual before starting this task because as a previous reviewer has stated some of the numbered steps in the assembly procedure seem to be out of order. If you don't want to undo and then redo some of the assembly then read the assembly steps ahead of time so you can move some of the later steps ahead of some of the earlier ones.

The Biesemeyer fence has two pieces of very heavy 6 foot long x 3 inch x 2 inch angle iron rails that need to be bolted to the Unisaw table, one rail bolts on the front of the saw and one rail on the back. The horizontal portion of the front angle iron rail has to be exactly 2 and 27/32 inch below the saw table surface. The bolting part can be done by one person but setting the correct height alignment on the front rail will require two people. Although an alignment template is supplied, the angle iron rail is so heavy that one person cannot hold it in alignment and at the same time tighten the bolts that hold it to the saw bed. Once again this is a two person task.

Now comes the interesting part, the assembly and installation of the side extension table. The extension table is made from hardwood with a laminate top. The directions tell you exactly how to attach the table outboard legs, unless of course you happen to have a mobile base, then the directions tell you that "the position of the legs will have to be changed to fit the mobile base extension". So it's up to you to figure out how to attach the legs in this case. In my case it wasn't difficult.

The extension table fits between the two angle iron rails that extend beyond the right side of the Unisaw table. The directions tell you to place the table between the rails and make sure that it mates with the edge of the saw table so that both are in the same horizontal plane, and to use a straight edge to make sure there is no discontinuity between the edge of the saw table and the extension table. Well this is ok except that the extension table is heavy, and there is nothing holding it up but the two legs on the one end. It is impossible to align the table with just two hands.

I ended up having to place one 2x4 underneath the angle iron rails at the egde of the saw table, and another 2x4 underneath the angle iron rails at the end of the rails to support the extension table between the rails. I held the 2x4's in place with two Quick clamps for each 2x4. Fortunately the top surface of the extension table when resting on the 2x4's is about an 1/8 inch below the top surface of the Unisaw. This enabled me to use opposing wood shims inserted between the support 2x4's and the bottom of the extension table to adjust the height so it was level with the saw table. I then discovered that there was a 1/32 inch bow in the middle of the extension table where it interfaced with the Unisaw. I had to take the now aligned table back to the work bench and add a hardwood stiffener to the edge of the table to eliminate the bow. Once this was accomplished I had to re-align the extension table, and then use an 8 foot pipe clamp that ran the entire length of the table to pull the extension table into the saw table edge, to remove a 1/16 inch gap between the two, and to hold it in place.

Once the table alignment and clamping is complete you have to drill several 1/4 inch holes through existing holes in the angle iron rails and through the wood sides of the extension table so you can attach 1/4 inch bolts to hold it in place. So far this was a great deal of work for what should be a simple tool assembly, and I'm still not completely sure that I got the extension table exactly on the same plane as the Unisaw table. For this reason I only drilled four holes and installed 4 of the supplied bolts so if some time down the road I decide that I need to re-align the table I will have several existing but un-drilled holes in the rails to drill new support holes for a newly aligned table.

The next step is to mount the Biesemeyer Guide Tube on top of the front angle iron rail. There are threaded holes on the Guide Tube that match up with holes on the rail. Although there are many holes, Delta only gives you 7 bolts and lock nuts to attach the tube to the rail. Don't be surprised if the holes in the rail do not exactly line up with the threaded holes in the Guide Tube. I could only get 6 of the 7 bolts in because some of the Guide Tube threaded holes were offset by as much as an 1/8th of an inch or so from the rail holes and the bolts wouldn't catch.

Here's a good tip. When you first begin the assembly of your new Unisaw, take off the motor cover and remove the Styrofoam block that keeps the motor in place during shipment. This piece of Styrofoam is beveled and is just right to use as a neck and head rest when your laying on your back installing the Guide Rail and the extension table legs. I found it very comfortable. When I was laying on my back on the shop floor, I had all the bolts and washers stacked in an orderly pile on the floor by my ear where they were easily accessed as I needed them. A couple of times I looked over and discovered all my bolts were gone. It turns out that my 8 month old Chihuahua had been busy taking one bolt at a time in his mouth and moving them to another stack he was making on the other side of the saw. I have a practical joker for a dog. I can hardly wait to see what he does with my shorts and socks.

Once the Guide Tube is installed it is very easy to install the Biesemeyer Fence. The adjustment of the fence to make it parallel to the blade, and the adjustment of the hold down lever were made more difficult then necessary because the assembly instructions dealing with that task seemed to be last minute additions to the assembly procedure and were out of order at the end of the manual.

The Biesemeyer fence system is fantastic. I am used to the rack and pinion fence on the DeWalt table saw that I've been using for the past several years and was a bit worried about the fact that you have to move the Biesemeyer fence by hand. My concerns turned out to be a non issue. The fence slides like it is on glass. It locks down parallel to the blade with little effort. The two adjustment allen screws that simultaneously set the hold down tension and the fence angle with respect to the blade are very simple to use. My one complaint would be that the allen screws were filled with grey paint and I had to clean them out before I could get an allen wrench in them.

Delta says that they do not supply a power cord for 5 horse power motors but my saw came with a power cord. I have standardized my 30 amp shop electrical service in that all of the 220 volt shop power receptacles are NEMA L6-30-R 30 Amp 250 Volt three prong lockable receptacles. The plug supplied by delta was for 20 Amp service and was incompatible with my outlets. Since I want all my 220 volt shop machinery to be compatible with my standard 220 volt receptacles, I removed the Delta power cord and plug and rewired the start/stop switch box with a new 8 foot long 300 volt rated 18 AWG 3 conductor cable and a NEMA L6-30-P 30 amp locking plug. There are many different types of 220 volt receptacles and matching plugs. Different types are designed for specific current loads and are purposely made so they are mechanically incompatible with one another. This helps you avoid doing things like plugging in a 30 amp machine into a 20 amp service. My apologies to Delta for modifying their fine machine, but I did what I had to do. By the way when the rewiring was finished, I turned the saw on and it didn't smoke.

I give the grade of B to the overall saw assembly task. There were a lot of assembly tasks that were left to the owner to do that required a bit of shop knowledge and shop tools, but the way I figure it, if the new owner is a novice in the shop he probably shouldn't have bought this bad boy in the first place.

____________________
Using the Saw
____________________

The first time I turned the saw on was to verify that my new wiring was done correctly. I did not have the large injection molded plastic motor cover installed. This cover helps direct the airflow for a shop dust collection system, and it also helps deaden the motor noise. Even with the cover removed, I was surprised to note that the saw ran very quietly. As a matter of fact it ran a lot more quietly even without the motor cover than my DeWalt saw does. So right away I was impressed. One day I will get a decibel meter to measure the noise the two saws put out. I'm betting the Delta noise level is on the order of 3 to 4 db down from the noise level of the DeWalt. If this is true then it's a significant noise reduction.

The saw blade height adjust wheel and the left tilt adjust wheel turn very smoothly with little effort on my part. Each wheel has an easily set lock down to maintain the settings for both the blade height and blade angle.

Before I actually used the saw I cleaned the entire cast iron saw table with mineral spirits to remove all packing grease, finger prints and other oils and dust deposited there from shipping and assembly. I then applied a thin coat of Johnson paste wax to preserve the metal and protect it from rusting.

The miter gauge appears to be well designed. It is sturdy and therefore heavy. It slides straight and true in the T slot in the saw table. I tried to move the miter gauge sideways when it was in the slot and I could not detect any lateral or angular movement. This translates to clean cross cuts with out error that would be caused by a miter gauge whose slot bar width doesn't precisely fit the width of the miter slot.

I was a little concerned initially about how the miter gauge slid along in the miter slot. It did not slide smoothly and the gauge tended to squeak as it rubbed against the table top. In addition when the gauge was pulled out past the table edge and then pushed back in, the gauge would catch on the front end of the saw table. This was not a good thing. After studying the situation for a bit, I ended up putting a 11/16 inch diameter washer between the gauge pivot screw and the slot bar, and a second 11/16 inch diameter washer between the gauge handle and the slot bar to raise the gauge about 1/32 inch above the slot bar. It now slides smoothly and does not catch the front end of the table. You need to raise both ends of the gauge so the front end maintains a 90 degree angle to the slot bar and therefore the saw table. There was nothing in the assembly manual that addresses this issue. If you need to make this adjustment do not use washers that have a diameter larger than 11/16 inch, otherwise they will be too wide to fit in the miter slot, and the gauge will not slide freely.

The Biesemeyer fence works great. It slides across the cast iron table and the extension table with ease and locks down firmly when the lock handle is depressed. The fence can be easily set to a maximum of 51 1/2 inches from the blade. The Biesemeyer fence can be visualized as a large T square with the T part sliding along between the front edge of the saw table and the Biesemeyer Guide Tube.

Pressure is applied between the guide tube and both the right and left ends of the T to keep the fence aligned parallel with the saw blade. As long as the T is between the table edge and the guide tube edge it remains in good alignment and parallel with the blade. When the fence is set to 51 1/2 inches from the blade the right portion of the T is at the far right edge of the guide tube. Moving the fence further than 51 1/2 inches from the blade causes the right portion of the T to move past the end of the guide tube. When this happens there is still locking pressure applied to the left end of the T but there is no longer any pressure applied between the right edge of the T and the tube and this causes the fence to angle right and looses its parallel alignment with the blade. So the maximum width of cut this saw will make with an extension table is 51� inches. This is still plenty good enough to accurately rip 4 x 8 sheets of plywood.

I tried to use the saw with the blade guard installed but found it cumbersome. The clear plastic guard extends beyond the front of the blade by a few inches and makes aligning the blade with a mark on a piece of stock very difficult to do. I like to be up close and personal with my blade so I can make accurate cuts. In case you're wondering, I still have all ten fingers. Anyways for this reason I removed the blade guard. Unfortunately the splitter is attached to the guard so when I removed the guard I had to remove the splitter too. Later when I get the guard and splitter separated I plan to re-install the splitter to keep pieces of long stock from binding the blade when ripping.

I tested the saw depth of cut and blade alignment by using a 4x4 chunk of redwood fence post. I chose a 4x4 that was 3 and 5/16 inches thick which is thicker than the maximum height of the blade. I set the blade to its maximum height and then made a cross cut on the end of the 4x4 about 1/8th inch in, which is less than the width of the blade. With the blade height set at its maximum height, I was able to make a 3 1/8th inch deep cut, leaving a 3/16th inch high shoulder along the top edge of the 4x4.

I tested the alignment of the miter gauge with the blade and the blade alignment with the table by rotating the 4x4 180 degrees and removing the shoulder that remained from the first cut. My objective was to make a second cut to remove the shoulder so it was even with the first cut. I then looked to see if the blade left any marks or cuts on the previously cut portion of the 4x4.

As I suspected even though the shoulder was removed clean as a whistle, the blade cut into the 4x4 on the high edge leaving another 3/16th inch thick shoulder, indicating the blade was not set to 90 degrees with respect to the table. I also noted that the shoulder was deeper at one end than it was at the other indicating that the miter gauge was not aligned to 90 degrees with respect to the blade. I adjusted the miter gauge stops by placing a square against the miter gauge and the blade using the very small adjustment allen bolt on the gauge. That eliminated the uneven shoulder on subsequent cuts but I was not able to get the blade to an exact 90 degrees with respect to the table. I don't know at this time whether or not there are adjustable stops for the left blade tilt. So at this point I am still getting about a 1/64th inch shoulders when I make the second cut of the two cut shoulder test. Basic Trigonometry tells me that my blade is off 90 degrees by 0.0047 degrees. This will result un-noticeable error for thinner pieces of stock but I want to get this fixed anyway.

I cut cross several pieces of wood of various thicknesses and then checked these against a square. All cuts were nice and smooth and clean. It appears the dust collector chute works as well. I won't know until I create more saw dust and then remove the motor cover to see how much sawdust has accumulated in the chute.

I give the table saw operation a grade of A. This is a very nice machine. I would have given this machine an A+ but I couldn't because I think the miter gauge adjustment I was forced to do was something that shouldn't have had to be done, and if so it should have been documented in the user manual. I expect to use this saw for a great deal of heavy duty work. I think for the price I paid for this saw I got a good bargain. This machine is the now center piece of my shop. Knowing what I know now, would I buy this saw again? The answer is yes I would.

It seems to be well made and ground to a fine finish but I can not see much improvement on my table saw. It seems to help more on my 12" chop saw and might help more if used with a thin kerf blade. I will continue to use it but cannot say for sure if it helps.

I use the stiffener with my thin kerf Forest II blade and it does take some of the "wobble" out. Well worth the price.

I am currently using this on my table saw. It lays up against the side of your blade, and helps to keep it true. Once in awhile I need to make a deeper cut, and it can get in the way for those cuts. I made some passes 2 1/2" deep and the edge of the Forrest stiffner stopped the piece. It is the first time I have had a problem with that.
Initially I installed this stiffner on a Sears Radial Arm saw because I was getting a good deal of wobble with it. Oddly enough, when I tried mounting a blade, then testing the trueness, only to loosen the nut, spin the blade slightly to a new seat, then retighten, and after a few tries, I hit it right, and the wobble disappeared. So whenever I replace a blade on that saw, I tweak it until it is right. Oddly enough, it runs so true when I do that, that I moved the Forrest over to the table saw.
I mated this stiffner up to the Forrest Woodworker II on my table saw, and I am getting cuts so smooth, you don't even have to sand the edge. It is finish quality perfectly smooth. (The Incra TSIII-32 table saw fence helps, giving me a true exact paralell line with the blade.)
So get the stiffner, make sure your fence is perfectly true, and you can forget about having to make your cuts a little bit oversized and having to finish up the edge on the jointer.
Highly recommended. The Forrest name is synonymous with the best in quality.

I have a couple of these HTC machine covers. The material seems of very high quality and I'd expect it to perform well overtime. After a couple of weeks in my garage shop, in the South Carolin summer, my covered tools seem to be doing just fine - no collected moisture and no rust. The construction is solid. This size cover works ok on my Dewalt planner, though there's a lot of excess material. I'd just as soon have grommet holes for bungee cords than the magnets. They aren't particularly effective at holding the cover neatly in place. Overall, though I'm satisfied with my purchase.

After years of battling light rust powder due to condensation I have finally found the solution. I have tried every thing from canvas to plastic and rubber covers, all sweat to a degree. I bought a couple of these machine covers and have found that they really work well. I would strongly recommend these machine covers to anyone with a rust problem.

Not Big enough for Table Saws as pictured but it covers every thing else..... Jig saws Belt sander's my 18 1/2 Planer etc. Magnet's keep cover in place while I blow down my shop and cover keeps most dust, dirt and dampness of my machine tops......... worth EVERY Penny! Buy several!

I've come back to edit this review after a year with this saw. I still like its positive traits...light weight, power, comfort, and smooth operation. It has plently of power to rip and crosscut pressure-treated wood and hardwoods. The saw is well-balanced, has a convenient stored blade wrench, and I like the adjustable dust nozzle. My gripes are also reinforced. I think they could do a better job of designing the cut depth adjustment to make the depth measurements and lever visible and accessible wihout having to peer through or around the handle. One of the DeWalt models does this. The bevel adjustment holds well and is reasonably accurate. I do wish they'd get away from the notched cutting guide on the front edge of the base...it isn't particularly accurate. The magnesium base construction is very light, durable, and acts as a very stable platform. They should also try to design in a couple cord hooks on the saw to make wrapping up the cord easier...after all the average upright vacuum has them. All-in-all an excellent saw that...thus far...is performing very well.

I have owned this saw for several years, and really like it. It is very powerful and runs smooth. I like the feature that the saw blade has a brake, and just doesn't just keep running.

Am I impressed or what? This is my first PorterCable product and based on its performance, this brand has won my loyalty. The first job for this tool was to cut up some 2X12 treated lumber from old bleachers into 8" souvenir sized pieces. I made more than 100 cuts in 2 hours. Although some of the boards which were damp offered slight resistance, this saw sang right through that wood with little effort and noise. It was light and easy to manuver. It made clean, smooth, consistant cuts, and the motor was barely warm when I finished. The job would probably have been a bit much for my 10 amp, 15 year old Black and Decker saw. This PorterCable saw with 15 amps of power made doing this big job a real pleasure! And its reasonably priced, too. Now, I have a quality framing tool. It's a must have for anyone with big sawing jobs to do. Thank's Amazon!

Not sure yet. You didn't send any assembly instructions with the unit. I would appreciate it if someone would either e-mail me or mail me the necessary documentation.

Bill Scott
2917 Misty Ridge Drive
Norman, OK 73071-4118

I gave new life to an old faithfull delta cabinet saw by adding a 30inch unifence and sliding table.The installation of the sliding table requires removel of the left extention wing,which now the hardware for the sliding table interfears with the fence. I called Delta about this combo and they said to cut off 8inches of the fence guide rail which would keep the mounting holes and the tape rule right where they should be.I could not see cutting a 270$ fence. By relocating the mounting holes ( two 1/2 holes)down eight inches to the left my 30in fence became a 38in fence I purchased a new sticky back rule and put over top of the old one.The only problem is the fence table you have to add 8inches to it. I made mine so there was no problem, or you could buy the 72in table and cut it down. I love the combination cross cutting has never been this easy and safe. Good Luck.

Was pretty easy to install, you will need a 7/16th drill bit for some minor drilling. Template was easy to use and pre drilled holes on bottom of fence can be used for power switch. The fence is easy to adjust and is a welcomed change from the craftsman fence. A must have wish I would have purchased this a long time ago.

I purchased the Biesemeyer T-Square Outside Miter Stop to use on my existing shop built "miter table system" that was made several years earlier. When the stop arrived I discovered that it would not fit my tables (at 1 1/2 inch the table rail was too wide). I was in the middle of a big project that needed to get done and decided to splurge and buy this 4 footer and a 6 foot table rather than build my own. When these arrived I was surprised to find the 4 foot table was 3/16 of an inch shorter than the 6 footer. I also found the 6 footer had a twist in it. The height difference was made up by stacking washers and twist was tamed by bolting it down.

These are robust and kind of pretty to look at but just the same - at these prices I'd expect more precision. If I was not in a rush I would have returned them and saved several hundred dollars by building them myself.

I purchased the Biesemeyer T-Square Outside Miter Stop to use on my existing shop built "miter table system" that was made several years earlier. When the stop arrived I discovered that it would not fit my tables (at 1 1/2 inch the table rail was too wide). I was in the middle of a big project that needed to get done and decided to splurge and buy this 6 footer and a 4 foot table rather than build my own. When these arrived I was surprised to find the 4 foot table was 3/16 of an inch shorter than the 6 footer. I also found the 6 footer had a twist in it. The height difference was made up by stacking washers and twist was tamed by bolting it down.

These are robust and kind of pretty to look at but just the same - at these prices I'd expect more precision. If I was not in a rush I would have returned them and saved several hundred dollars by building them myself.

Its hard to review this type of product

I like this table without it cutting identical lenght would be hard set a stop and cut away knowing all your cuts will be the same length.

It needs to be setup with you miter saw properly to work right but it is not a difficult task.

It even has a gape to let saw dust drop threw for more accurate cuts

Very well made and a must for identical leghts cuts.

If 6 foot is to long or to short they come in smaller and longer lenghts if you get the 6 foot get a 12 foot self stick tape measure if not you will come up short

Hello to those interested,
I feel it necessary to alert those interested in purchasing the 10" Hitachi dual compound saw. With my recent purchase and set up of this saw I was surprised to note the inability to compound to the left of any more than 30 degrees. With the addition of a tightening nut on the side of the chip guard which hits the fence when sliding!!! I believe this is an addition to the saw of recent months and may not be a problem on older models. I hope Hitachi will rectify this probblem ASAP.

Sincerely,

Richard W. Grieves d.b.a.
Cape Shorew Woodworking

This is a great saw. The cuts produced are as smooth as glass and really do not need any sanding. This beats all the other miter saws I have ever used and with its sliding capability it nearly eliminates the need for a radial arm saw. I use mine for general woodworking and home repair and have found it to be indispensable. Great saw and well worth the investment.

We have used the Hitachi 8 1/2" saw at work for a five or six years now. We have never had any problems at all with it. But when I decided to buy my own saw, I check out other brands, too. The Makita was a close second, but since I know of at least 3 people that have the Hitachi 10" and haven't had a single problem, that is what I chose. It has every feature that I would possibly need. It even has positive stops that aren't even listed on the specs. The saw that I received came with 2 blades... a 40 tooth and a 72 tooth. I highly recommend the Hitachi.